Rampas de acceso para platos giratorios de perfil bajo ASWG004
Rampas de acceso para platos giratorios de perfil bajo ASWG004
Level the entry.
Level the whole car.
Your ASWG004 turn plates sit 1" off the floor. Drive straight at that step and the tire shifts the plate off its mark before it ever climbs on. ASRP004 raises every wheel to the same 1" height, so the car rolls on level, sits level, and settles level.
Roll onto the plates without moving them.
The same corner, with and without the ramp.
Driving straight onto the plates
A 1" step meets the tire before the plate does. The tire nudges the plate along as it climbs: the plate skids off center, and the floating top plate jams against its travel stop. The dial ends up pointing somewhere it should not, and you start the alignment with a moved plate, not a centered one.
Rolling on with ASRP004
The ramp carries the wheel up the full 1" and hands it over level with the plate deck. The tire rolls across the bridge onto the plate instead of striking its edge, so the plate stays centered under the wheel and the top plate keeps its free float. Roll on, settle, and start from a centered plate.
Five engineered details. One level stage.
Hover or tap each point to see what carries the car.
1" deck, matched to the ASWG004
The deck finishes at the same height as the ASWG004 turn plate seat, so the transition bridge lies flat and the wheel crosses without a lip either way.
1" deck, matched to the ASWG004
The deck finishes at the same height as the ASWG004 turn plate seat, so the transition bridge lies flat and the wheel crosses without a lip either way.
From flat panels to a level stage.
Slide-lock assembly, ramp placement, drive-on, and plate staging. Start to finish.
Four steps to a level car.
Step 01 / Set the Floor
Work on flat, hard concrete or paved floor. Skip sloped driveways, gravel and soft ground. The floor is the reference everything measures against.
Step 02 / Drive On
Ramp centerline to wheel centerline, longer units to the rear. Roll on at walking pace and stop on the flat deck. Do not overshoot.
Step 03 / Stage the Plates
Set an ASWG004 turn plate in front of each front wheel, plate center matched to wheel center. Shift outward on wide tires so the dial stays visible.
Step 04 / Bridge and Settle
Drop the ASWG004-TSB bridges in, roll the front wheels onto the plates, chock the wheels, and let the car settle before you read anything.
Why the ASRP004.
The staging layer of the AutoSolo system, built to the ASWG004's numbers.
Level All Four Corners
The ASWG004 turn plates hold your front wheels 1" off the floor. These ramps raise the rear wheels to the same 1" height, so all four wheels sit at one level while you set up your at-home wheel alignment.
Four Ramps, Two Level Platforms
You get a ramp for every wheel plus two rear level platforms, so the whole car comes up level, not just the front. Every corner ends at the same height. The ASWG004 turn plates are sold separately.
1" Height Match
The ramp deck finishes at the same 1" height as the ASWG004 turn plate seat, so the ASWG004-TSB transition bridge lies flat and the wheel crosses without a lip in either direction. The face rises only 1" over about a 2.5" run.
4 Tons Per Ramp
Each ramp is rated to 4 tons, the same rating as the ASWG004 turn plate it feeds. That handles cars, SUVs and light trucks with margin to spare, and keeps the whole staging system on one limit from ramp to plate.
Nothing Extra to Buy
The ASWG004-TSB transition bridges that span ramp to plate ship standard in every ASWG004 box. You already own them. No separate purchase to finish the ramp-to-plate transition.
Tool-Free Slide-Lock
Panels snap together by hand, the female slot dropping over the male tab until it locks. Build the set in about a minute, break it down just as fast, and stow it flat.
Oil and Chemical Resistant
Molded polypropylene shrugs off oil, brake fluid and shop chemicals. It will not rust or splinter the way wood blocks and steel plate do over a few seasons.
Built for the ASWG004, Not the ASWG008
Sized to the ASWG004 Low Profile Turn Plate, sold separately. It does not fit the ASWG008 pit-rack plate, which sits at a different height.
Hard, Flat Floors Only
Use on concrete or paved floor. Not rated for sloped driveways, gravel, dirt or soft ground. Built to stage a vehicle for alignment work, never as a vehicle lift, a jack stand, or fall protection.
Take the Alignment In-House
Stage all four corners level in your own garage and read camber, caster and toe at ride height. AutoSolo puts suspension work in your hands without a five-figure machine.
The plates it feeds, and the kit that bundles both.
Where the ASRP004 sits, and the two ways to complete the setup.
Herramientas fiables. Soporte al que puede llegar.
Para aficionados y mecánicos caseros
Lo usan en todo el mundo mecánicos, entusiastas y constructores para resultados constantes.
Probado en talleres reales
Usado y valorado por creadores del motor y especialistas en alineación en todas las plataformas.
Soporte en su idioma
Escríbanos en español, inglés, alemán, francés o italiano. Cada solicitud de soporte recibe respuesta en un día hábil.
1 año de sustitución
Si aparece un defecto de fabricación, nuestro equipo ofrece asistencia y recambio con rapidez.
ENTENDER LA COLOCACIÓN DEL NIVEL
El AutoSolo ASRP004 es un conjunto de rampas y plataformas de nivelación para subir el vehículo, diseñado para posicionar un vehículo para la alineación de ruedas a la misma altura de 2,54 cm que los platos giratorios de bajo perfil ASWG004. Diez paneles de polipropileno con bloqueo deslizante se ensamblan a mano en 4 rampas de acceso y 2 plataformas niveladoras traseras, sin necesidad de elementos de fijación. Las ruedas delanteras suben por sus rampas, cruzan los puentes de transición ASWG004-TSB incluidos en cada caja del ASWG004 y se asientan sobre los platos giratorios; las ruedas traseras quedan sobre las plataformas niveladas, de modo que las cuatro esquinas se apoyan en un mismo plano a la altura de marcha. Conducir un neumático directamente sobre un plato sin rampa tiende a descentrarlo y a trabar su placa superior flotante contra el tope de recorrido, por lo que el acceso mediante rampa es lo que mantiene cada plato centrado y libre antes de ajustar el camber, cáster, KPI y la convergencia. Cada rampa tiene una capacidad nominal de 4 toneladas, la misma capacidad que el plato giratorio al que sirve, lo que cubre automóviles, SUV y camionetas ligeras. El polipropileno moldeado resiste el aceite, el líquido de frenos y los productos químicos del taller, y se guarda plano entre alineaciones. El conjunto es compatible únicamente con el ASWG004; no es compatible con el plato para foso ASWG008, que se sitúa a una altura diferente. Utilícelo sobre suelos de hormigón duro y plano o pavimentados para posicionar un vehículo para trabajos de alineación; no es un elevador de vehículos ni un soporte de gato. Dentro del sistema AutoSolo, el ASRP004 es la base de soporte bajo las herramientas de medición: los platos giratorios ASWG004 sostienen las ruedas delanteras, la abrazadera de rueda y el medidor de camber, cáster y KPI toman las mediciones, y el kit Comfort ASWG0401CMF incluye platos, rampas, abrazadera y medidor en una sola caja.
User Manuals
Verified owner reviews
What owners say
Ratings and reviews are supplied by Judge.me from verified purchases.