Language
ViewDownload PDFOther manuals

Drive-on ramp

ASRP004•Leveling platform
Tutorial available on autosolotools.com
User Guide
AutoSolo · ASRP00401

01 · Setup

About the ramp.

The ASRP004 Drive-On Ramp is a leveling platform designed for use with AutoSolo ASWG004 Turn Plates. It bridges the height difference between the floor and the turn plate surface, creating a smooth, level entry path for the vehicle. This prevents suspension distortion caused by a sudden step at entry, so your alignment measurements stay repeatable.

Box contents

The kit includes 6 square panels and 4 ramp panels. Panels connect using slide-in locking inserts. Lift the female slot over the male tab and slide it into position until locked.

Assembly

For the front ramps, connect one ramp panel to one square panel. For the rear ramps, connect one ramp panel to one square panel, then attach a second square panel to the back of the first square panel.

  • 2× Front wheel drive-on ramp platforms. Shorter.
  • 2× Rear wheel drive-on ramp platforms. Longer.

Note: Turn plates (ASWG004) are sold separately.

!Read before use

  • This ramp is designed for wheel alignment setups only. Do not use it as a vehicle lift or jack stand.
  • Always work on a flat, level, hard surface (concrete or paved floor).
  • Do not use on sloped driveways or soft flooring.
  • Ensure the vehicle weight does not exceed the ramp load rating.
  • Keep bystanders clear during the drive-on step.

Instructions

1

Prepare your surface

Choose a flat, level, hard floor. Avoid sloped driveways, uneven concrete, or soft surfaces. Alignment readings depend on a level surface.
2

Position the ramps

Place the four ramp platforms in front of the tires. Position longer ramps toward the rear and shorter ramps toward the front. Align each ramp so its centerline matches the center of the corresponding wheel.
Do not place the turn plates yet.
Drive-on ramp · User guide01
Instructions02
3

Drive onto the ramps

Start the vehicle. Slowly roll forward onto the ramp platforms. Stop as soon as the vehicle reaches the flat section of the ramp.
Do not overshoot the platform.
4

Position the turn plates

Place one ASWG004 Turn Plate in front of each front ramp platform. Align each plate so its rotational center matches the wheel centerline.
Wide tires: Shift the turn plates slightly outward. Confirm the degree indicators remain visible.
5

Install transition bridges

Place one transition bridge between each front ramp platform and the turn plate. Slowly roll the vehicle forward onto the turn plates.
6

Center the wheels

Roll each wheel so it is centered on the turn plate surface. This step may require multiple attempts.
Tip: A second person acting as a spotter makes this step easier.
7

Insert wheel chocks

Remove both transition bridges. Remove the front ramp platforms if desired. Leave the rear wheels on their platforms. Insert wheel chocks to prevent unexpected movement. Allow the suspension to settle fully before taking measurements. The vehicle is ready for alignment.
Drive-on ramp · User guide02

Compatible products

ASWG004

AutoSolo Low Profile Turn Plates (Pair)

ASWG004-TSB

Transition Bridges for ASWG004

ASWG008-WC

Wheel Chock for AutoSolo Turn Plates

Troubleshooting

Vehicle overshoots the ramp platform

Approach more slowly. Roll at a walking pace during drive-on. Stop more frequently to ensure turn plate centering.

Turn plate shifts when rolling forward

Recheck the transition bridge position before rolling. The bridge must be fully seated between the ramp and the plate.

Wheel will not center on the plate

Recheck the turn plate center line alignment with the wheel.

Alignment readings are inconsistent

Confirm the floor is level. Move to a flatter surface if needed.

Visit our websiteautosolotools.com
For technical questions email or call us atsupport@autosolotools.com
415.849.0275
ASRP004User Guide · v2.0 · 2026-11
©AutoSolo® 2026
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced without the express written consent of AutoSolo.